Paint, Drywall & Flooring · Painting & Measurement
How Much Paint Do I Need for a Room?
Estimate room paint from paintable surface area, coats, and coverage for the exact product and surface.
Paint needed = paintable surface area × number of coats ÷ product coverage per gallon. Measure walls and ceiling separately, subtract openings that will not be painted, and use the coverage on the paint label.
Room dimensions alone do not determine the purchase quantity. Wall height, doors and windows, ceiling inclusion, coats, product coverage, and surface condition all affect the estimate. The Paint Calculator keeps those inputs visible so you can check the assumptions.
Measure the wall surfaces
For a rectangular room with a shared wall height, add the areas of the two pairs of opposite walls:
Gross wall area = 2 × (room length + room width) × wall height
Measure inside wall-to-wall dimensions in one unit. If the room is not rectangular or has different wall heights, measure each paintable wall section and add the areas instead of using a single room perimeter formula. Break gables, alcoves, and other irregular sections into simple shapes and keep each measurement on a sketch.
The ceiling is a separate surface. For a flat rectangular ceiling, its area is length × width. Include it only when you intend to paint it with the paint and coverage being estimated. A vaulted or angled ceiling needs its actual sloped surface area, not the floor footprint.
Decide which openings to subtract
Subtract doors and windows that will not receive the wall paint. For an opening with a rectangular shape, multiply its width by its height. If multiple openings share a size, multiply that area by the count. Add the opening areas, then subtract the total from gross wall area:
Net wall area = gross wall area − openings not being painted
Do not subtract an opening if you will paint that surface with the same product and want it included in the estimate. Trim, door faces, window frames, and closet interiors are separate paintable surfaces; measure them independently. For a room with different window sizes, measure each size group separately or enter their combined area as an additional opening total.
Apply coats and product coverage
Multiply the net paintable area by the number of coats. Then divide by the stated coverage per gallon:
Gallons needed = paintable area × coats ÷ coverage per gallon
Use the exact product's label or technical sheet. Sherwin-Williams describes 350–400 square feet per gallon as typical, while noting that requirements vary with application method, surface type, and condition. That range is a reference point, not a guarantee for another brand or a particular wall. Check the Sherwin-Williams Paint Calculator guidance and use the figure for your product.
Check a worked example
Consider a rectangular room measuring 12 ft × 10 ft with 8 ft walls, one 3 ft × 7 ft door, and two 3 ft × 4 ft windows. Exclude the ceiling and paint the walls with two coats.
- Gross wall area:
2 × (12 + 10) × 8 = 352 ft². - Door and window openings:
(3 × 7) + 2 × (3 × 4) = 45 ft². - Net wall area:
352 − 45 = 307 ft². - Area across two coats:
307 × 2 = 614 ft². - At an editable example coverage of 350 ft² per gallon:
614 ÷ 350 = 1.7543 gallons.
That is the calculated quantity under those inputs. If buying only one-gallon cans, the estimate rounds up to two cans. Smaller or larger packages may be available, so the purchase combination depends on the product.
Adjust for the surface and product
Coverage is not a universal constant. A rough, porous, unsealed, or previously unpainted surface can use paint differently from a smooth, prepared wall. Application method and product instructions also matter. Do not add a generic percentage and assume it fits every project; check the manufacturer's preparation and coverage guidance, then adjust the editable coverage input to match.
The coat count should also follow the product directions and the finish you need. Primer is a separate product and is not included in this paint estimate. If you need primer, measure the relevant area and estimate it using that product's coverage separately.
Avoid common estimating errors
- Mixing feet and inches without converting them before calculating area.
- Using floor area as the wall area or adding the ceiling by default.
- Counting openings twice, or subtracting a door that will be painted with the same product.
- Applying coverage to one coat when the project needs multiple coats.
- Using a generic coverage number instead of checking the selected paint.
- Treating fractional gallons as a promise about available can sizes or the exact amount left over.
FAQs
Do I include the ceiling in a room paint estimate?
Only if you plan to paint it. Add the actual ceiling area separately; a flat rectangular ceiling uses the room length times width, while a vaulted ceiling needs its sloped surface measurement.
Should I subtract windows and doors?
Subtract openings that will not receive the wall paint. If you are painting a door or trim with the same product, estimate those surfaces separately rather than subtracting them and then counting them again.
How much paint do I need per square foot?
For one coat, divide one gallon by the exact product's stated coverage per gallon. At 350 ft² per gallon, that is about 0.00286 gallons per square foot for one coat; for two coats, double it. Sherwin-Williams lists 350–400 ft² per gallon as a typical range, but surface and application affect coverage. For a room estimate, calculate the paintable wall and ceiling area first rather than multiplying the floor area by this rate.
How do I estimate paint for a room that is not rectangular?
Measure each wall section separately, divide irregular shapes into rectangles or triangles, and add the paintable areas. Do not use the rectangular-room perimeter formula for a room with missing walls, additions, or different wall heights.