Conversion · 22 calculators live

Conversion Calculators

Convert the measurements a project or everyday task is actually specified in: land area, square units, cubic volume, gallons, liters, pounds, kilograms, temperature scales, kitchen volume, and board feet.

Each tool states its unit basis, shows the formula with your numbers, and keeps the exact decimal separate from practical display rounding. Conversion stops where material behavior begins: density, compaction, bag yield, ingredient weight, and price belong to tools that ask for them explicitly.

Read moreRead less

These pages cover the conversions that come up when a measurement is quoted in the wrong unit: a lot listed in acres, a plan measured in inches, a liquid container labeled in gallons, a recipe using cups, lumber sold by board feet, or a package specified in pounds and kilograms.

Every result states the unit it is in and the factor behind it, so the arithmetic can be repeated on paper. Where a conversion has more than one legitimate basis — most notably the international foot and the legacy U.S. survey foot — the page names the basis it uses instead of leaving the difference implicit.

If the next step is buying material rather than converting a measurement, move to the construction calculators. They add density, package yield, allowance, and price, and they keep those values separate from the conversion itself.

Pick the converter for what you measured

The tools are grouped by the quantity you start with. Each one accepts several units and shows the formula it applied, so the result can be checked by hand.

Land area

Use the acreage calculator when you already have a measured area or the two sides of a rectangular parcel. It converts between acres, square feet, square yards, square meters, hectares, and square miles, and states the acre basis it uses.

Area conversion

Use the square-inch converter when a small product, plan, or material specification gives area in a different unit. Area factors are squared, so one square foot is 144 square inches.

Length

Convert inches to decimal feet, or go the other way and read the result as feet and inches with a fractional tape-measure reading. The fraction is a display convention; the exact decimal remains the value used in the conversion.

Unit facts these calculators rely on

These definitions are exact on the international-foot basis used across the site. Values in results may be rounded for display, but the conversion itself is not.

UnitEquivalent
1 acre43,560 ft² = 4,840 yd² = 4,046.8564224 m²
1 square mile640 acres = 2.589988110336 km²
1 square yard9 ft²
1 cubic yard27 ft³ = 0.764554857984 m³
1 cubic foot0.028316846592 m³ = 1,728 in³
1 foot12 inches = 0.3048 m
1 meter3.280839895 ft (display rounding)
1 hectare10,000 m² = 2.47105381467 acres (display rounding)
1 U.S. liquid gallon231 in³ = 3.785411784 L
1 pound0.45359237 kg
1 avoirdupois ounce28.349523125 g
1 board foot144 in³

Basis: international foot, with factors listed in NIST Special Publication 811, Appendix B.9. Legacy U.S. survey-foot records can use a slightly different basis; the acreage calculator explains when that distinction matters.

Exact value, then display rounding

Rounding happens at the end, for reading, not in the middle of the arithmetic. A result shown as 1.48 yd³ means 1.481481… yd³ before display; if the number feeds another step, use the exact figure or re-enter the unrounded value.

Tape-measure fractions such as 3 5/8 in are reading aids. The inches-to-feet calculator keeps the exact decimal and shows the fraction alongside it, so choosing a nearest-1/16-inch reading does not silently change the length used for the conversion.

Where conversion ends and ordering begins

Cubic yards describe a volume, not a delivery. A supplier sells a product with a density, a compaction behavior, a package size, and a price, and those are not properties of the unit. Ordering therefore needs a separate decision about the extra allowance, the load size, and the minimum quantity. The bulk material calculator and the concrete calculator ask for those values rather than hiding them inside a conversion.

Conversion calculator questions

Which acre does the acreage calculator use?

It uses the international acre: 43,560 international square feet, or 4,046.8564224 square meters. That is the definition used in current U.S. customary conversion tables. Legacy records based on the U.S. survey foot differ by about 4 parts per million, which matters for boundary surveys but not for an area estimate.

Should I use cubic feet or cubic yards?

Choose the unit the answer needs to be in. Cubic feet is convenient for box-sized spaces, appliance or shipping dimensions, and interior volume. Cubic yards is convenient when a supplier sells loose material by the yard. The conversion between them is exact: 1 yd³ = 27 ft³, and both volume calculators show the equivalent in the other unit.

Can I convert square feet to cubic yards directly?

Not without a depth. Area has two dimensions and volume has three, so the conversion needs the depth of the layer: cubic yards = square feet × depth in inches ÷ 324. The cubic yards calculator has an area-and-depth mode for exactly that calculation.

Why don't these tools include density or price?

Density, compaction, bag yield, and price belong to a specific material and supplier, not to a unit. Applying a default would make a clean conversion look like a purchasing quote. The bulk material and concrete calculators ask for those values explicitly and keep them separate from the volume.

Guide hubs for these calculations

Worked methods for measuring area, checking unit bases, and turning a conversion into an order.

  • Area, Volume & Material OrdersConvert land area, calculate cubic feet and cubic yards, and turn an area and depth into a bulk-material order without confusing volume with weight.
All guide hubs

Other calculator collections