Roofing & Exterior · Roofing & Measurement

How to Measure Roof Pitch from Inside the Attic

A roof labeled 6/12 rises 6 inches for every 12 inches of horizontal run; measure rise and run, not the rafter's sloped length.

Roof pitch = vertical rise ÷ horizontal run. In U.S. roof notation, the second number is often fixed at 12, so a 6/12 roof rises 6 inches over 12 inches of horizontal distance.

Roof pitch describes steepness as rise over horizontal run. You can measure it from an accessible rafter in an attic using a level and tape; you do not need the sloped rafter length. The Roofing Calculator accepts rise per 12 inches of horizontal run to estimate sloped area and shingle bundles. This guide covers the separate task of obtaining that pitch input; the calculator does not measure a roof for you.

What a roof pitch number means

A pitch written 6/12 means the roof rises 6 inches for every 12 inches of horizontal run. The ratio can be simplified mathematically, but carpentry and roofing measurements commonly keep the run at 12 inches so pitches are easy to compare. A 3/12 pitch rises 3 inches per foot of horizontal run; a 9/12 pitch rises 9 inches per foot.

Pitch is not the same as angle. Pitch is a rise/run ratio; angle is usually expressed in degrees. Keep the measured rise and the run together in your notes so someone reading the result does not mistake a 6/12 ratio for six degrees.

Measure pitch from an accessible rafter

  1. Choose a sound, accessible rafter in the attic. Avoid measuring from a ceiling joist unless you have confirmed it is parallel to the roof slope.
  2. Hold a level horizontally against the side or underside of the rafter. Check the bubble so the level is truly horizontal.
  3. Mark a 12-inch horizontal distance along the level from the point where it meets the rafter.
  4. At that mark, measure the vertical gap from the level to the rafter. That gap is the rise for a 12-inch run.
  5. Record the actual measurement, such as 7.25 in rise / 12 in run, before deciding whether a plan uses a nearby standard pitch label.

If a 24-inch level is easier, measure rise over a 24-inch horizontal run and divide the rise by two to express it per 12 inches. More generally, rise per 12 = measured rise ÷ horizontal run × 12 when both values use the same unit.

Worked example: a 7-in rise

Suppose the level is horizontal for 12 inches and the rafter is 7 inches above it at the far mark. The measured pitch is 7/12. Across a 24-inch horizontal run, the same roof would rise 14 inches if the slope is uniform: 14 ÷ 24 × 12 = 7 inches per foot.

Do not round the field measurement automatically to 7/12 or 8/12 if it falls between those values. Use the exact measured rise for an area estimate, and use the design plans or a roofing professional when the pitch label affects material selection or installation requirements.

Convert pitch to an angle

For a pitch of rise/12, the angle from horizontal is angle = arctan(rise ÷ 12). A 6/12 pitch has an angle of arctan(0.5), about 26.6°. This conversion is useful when software asks for an angle, but roof-area formulas may ask for pitch or a slope factor instead. Confirm which quantity the tool expects.

Once the pitch is recorded, calculate the roof's sloped area from its horizontal footprint using the matching rise-over-12 value.

Do not treat measurement as roof-access guidance

This method is for an accessible interior measurement. It does not tell you how to climb, walk, or work on a roof. If the rafter cannot be reached safely from the attic, use drawings or have a qualified roofing professional measure it. OSHA's residential construction fall-protection guidance addresses fall hazards for workers performing roofing and other residential construction activities (checked October 20, 2026); its workplace guidance is not a DIY access procedure.

FAQs

Is roof pitch the same as roof slope?

In everyday U.S. roofing use, the terms are often used for the roof's steepness. Record the actual rise and horizontal run because different tools may ask for a ratio, angle, or multiplier.

Can I measure pitch from the ceiling inside a room?

Usually not from a flat ceiling alone. Use an accessible rafter, reliable building plans, or a qualified professional; the ceiling plane may not match the roof slope.

Is a 6/12 pitch a 6-degree roof?

No. Six inches of rise per 12 inches of run corresponds to an angle of about 26.6°, not 6°.