Concrete & Masonry · Concrete & Materials

How to Calculate Concrete for a Rectangular Footing

Convert every footing dimension to feet, multiply length by width and depth, then keep the net volume visible before planning bags or ready-mix.

Rectangular footing volume = length × width × depth × quantity. Convert all three dimensions to the same unit first. With feet as the working unit, divide cubic feet by 27 to get cubic yards.

Use the Concrete Calculator in Rectangular footing mode when the pour has a consistent rectangular cross-section. This guide shows how to measure the concrete dimensions and check the result; it does not size or approve a footing design.

Rectangular footing volume formula

For one rectangular footing, multiply its length, width, and depth. If you have several identical isolated pads, multiply by their count. If the foundation changes size or direction, calculate distinct sections and make sure their volumes do not overlap.

Volume (ft³) = length (ft) × width (ft) × depth (ft) × quantity

Volume (yd³) = volume (ft³) ÷ 27

The formula describes only the concrete prism. It does not determine the footing dimensions required for a building, soil, load, frost, drainage, or local code conditions. Use the project plans and applicable local requirements for those decisions.

Measure the concrete dimensions

Use the dimensions of the concrete form or planned pour, not a convenient outside measurement that includes loose soil. Record length, width, and depth separately. Footing depth is the concrete thickness in this volume calculation; do not mix it with an excavation depth that also includes gravel, working space, or other material.

For a straight continuous footing, measure each distinct run. If two runs meet at a corner, sketch how the sections join and avoid counting the shared corner block twice. For separate pad footings with identical dimensions, use the quantity input; for pads of different sizes, calculate each size group separately and add the volumes.

If dimensions are mixed, convert first. For example, 16 inches is 16 ÷ 12 = 1.333… feet. Keeping the fraction through the multiplication avoids a small rounding error at every step.

Worked example: a 20-foot footing

Suppose the measured concrete section is 20 ft long, 16 in wide, and 8 in deep. Convert both inches to feet: width = 16 ÷ 12 = 1.333… ft and depth = 8 ÷ 12 = 0.666… ft.

20 × 1.333… × 0.666… = 17.777… ft³

Then 17.777… ÷ 27 = 0.6584 yd³, or about 0.66 yd³ before any allowance. This is a geometry example only; use the dimensions on the applicable plan rather than copying them for a real project.

Convert volume to yards or bags

Ready-mix is commonly quoted by volume, so keep the cubic-yard figure unrounded while comparing it with the supplier's ordering increments. Ask the supplier how its minimums and increments work; the calculated net volume alone does not establish the delivery quantity.

For bagged mix, divide cubic feet by the product's stated yield per bag and round the final count up. A bag's weight does not tell you its finished yield. See how to calculate concrete bag count for a documented yield example and the separate allowance step. The calculator can show bag counts when you select a package yield or enter the yield from the product label.

Keep extra material separate

First record the net geometric volume. Only then decide whether an allowance is appropriate for measurement uncertainty, form irregularity, spillage, or placement conditions. A single percentage is not right for every footing, so the worked example above intentionally has no automatic extra volume.

If the plan has multiple sections, calculate and add their unrounded volumes before converting or rounding a shared order. If sections must be poured as separate batches or use different mixes, plan each one on its own and follow the supplier's ordering guidance.

Know what this estimate leaves out

This method models straight rectangular concrete only. It does not subtract reinforcement, account for stepped or tapered footings, determine excavation quantity, or specify reinforcement and connections. Break non-rectangular pours into dimensions the model supports, or use a takeoff that matches the actual shape.

Most importantly, a volume estimate is not a structural design. It cannot establish whether a footing is adequate for a structure or suitable for site soil and conditions. Do not use the calculator to choose footing dimensions in place of plans or local professional guidance.

FAQs

How do I calculate concrete for a continuous footing?

For a straight section with a constant rectangular cross-section, multiply its length by its width and depth after converting to consistent units. Split a changing layout into non-overlapping sections, then add their volumes. The formula estimates quantity only; it does not design the footing.

How many cubic yards is 20 ft × 16 in × 8 in?

Those dimensions equal about 17.78 ft³, or 0.658 yd³, before an allowance. Convert both inch measurements to feet before multiplying.

Can I use footing volume to choose footing size?

No. The calculation returns volume for dimensions you supply. Use applicable plans and qualified local guidance to determine the footing dimensions and construction requirements.