Concrete & Masonry · Concrete & Materials
Fence Post Concrete Calculator: How Much Concrete Per Post?
A post hole is a cylinder minus the post. Measure the concrete fill height, subtract the embedded post volume, then divide by the bag yield and round up.
A fence post hole is a cylinder minus the post. For a 10-inch-diameter hole with 3 ft of concrete fill and a 3.5-inch-square post, the gross cylinder is about 1.636 ft³; subtracting the post leaves about 1.381 ft³. At 0.375 ft³ per 50 lb bag, that is 3.68 bags, rounded up to 4 bags. At 0.60 ft³ per 80 lb bag, it is 2.30 bags, rounded up to 3 bags.
The Fence Post Concrete Calculator calculates the gross cylinder, subtracts post displacement, and estimates bags for one or many identical posts. Use this guide to check the measurement and product-yield assumptions before ordering.
These numbers are arithmetic examples, not a recommended hole size or concrete specification. Follow the project plan, local requirements, and the product instructions.
The short answer
There is no single bag count for a fence post. The amount depends on:
- the diameter of the hole;
- the depth of concrete, not the full hole depth;
- the post size and how much of it is embedded;
- the bag yield of the concrete product;
- the number of posts and how you batch the work.
A post hole concrete calculator normally asks for the same three inputs: hole diameter, concrete fill height, and post size. A larger hole, a deeper concrete fill, or a larger post displaces more volume. Always calculate the net concrete volume first, then convert it to bags.
Measure the hole and the concrete fill height
Measure the average diameter of the hole. A hole that is wider at the top than the bottom should be measured in a way that represents the actual volume; for a rough estimate, use an average diameter and note that the result is approximate.
Measure the concrete fill height, not the total hole depth. The concrete does not usually fill the entire hole:
- gravel at the bottom takes up depth;
- the concrete may finish below grade;
- the post may sit on the gravel rather than at the bottom of the hole.
QUIKRETE's guide to setting posts says to dig the hole about three times the width of the post, with a depth equal to one-third to one-half of the above-ground post length plus 6 inches. It also recommends a 6-inch gravel base and filling the concrete to about 3–4 inches below ground level. Those are manufacturer instructions for its method, not a universal code requirement.
For a post with 6 ft above ground, that guidance puts the hole depth at roughly 2.5–3.5 ft before considering the gravel layer and the finish height. The concrete fill height is smaller than the total hole depth.
Use the depth required by your project, frost conditions, and local building department. A fence post in a cold climate may need a deeper hole than the same post in a warm climate.
Subtract the post volume
Treat the concrete as a cylinder with the post removed:
Gross hole volume = π × (diameter ÷ 2)² × concrete fill height
Post volume = post width × post depth × concrete fill height
Net concrete = gross hole volume − post volume
Use feet for every dimension before multiplying. If the post is not embedded through the full concrete height, subtract only the embedded portion.
For a post that measures 3.5 in square, the post width is 3.5 ÷ 12 = 0.2917 ft. The post area is 0.2917 × 0.2917 = about 0.0851 ft². A 4×4 post is often described as 3.5 in square, but measure the actual post rather than assuming every product is the same.
If the hole is irregular, the cylinder formula is still a planning approximation. A hole that is much wider at the top, or that has a bell shape, needs a different volume model.
Worked example: one 10-inch post hole
Inputs for the arithmetic:
- hole diameter: 10 in
- concrete fill height: 3 ft
- post: 3.5 in square
- concrete: 50 lb bag yielding 0.375 ft³, or 80 lb bag yielding 0.60 ft³
Gross cylinder:
- radius = 10 ÷ 12 ÷ 2 = 0.4167 ft
- area = π × 0.4167² = 0.5454 ft²
- volume = 0.5454 × 3 = 1.636 ft³
Post volume:
- 3.5 ÷ 12 = 0.2917 ft
- area = 0.2917² = 0.0851 ft²
- volume = 0.0851 × 3 = 0.255 ft³
Net concrete:
1.636 − 0.255 = 1.381 ft³
Bags:
- 50 lb at 0.375 ft³: 1.381 ÷ 0.375 = 3.68, rounded up to 4 bags
- 80 lb at 0.60 ft³: 1.381 ÷ 0.60 = 2.30, rounded up to 3 bags
If you ignore the post and use the gross 1.636 ft³, the 50 lb estimate becomes 4.36 bags, rounded up to 5 bags. That is one extra bag in this example. For a small number of posts the difference may be small; for a long fence it adds up.
Bags, multiple posts, and batching
Use the yield printed on the exact product. For the products cited here:
| Product example | Bag size | Approximate yield |
|---|---|---|
| QUIKRETE Fast-Setting Concrete Mix | 50 lb | 0.375 ft³ |
| QUIKRETE Fast-Setting Concrete Mix | 60 lb | 0.45 ft³ |
| QUIKRETE Concrete Mix No. 1101 | 80 lb | 0.60 ft³ |
Do not mix yields from different products. A 50 lb bag of one mix and a 50 lb bag of another can produce different finished volumes. If your product is not listed, use the volume on its package or technical data sheet.
Multiple posts:
For 8 identical posts with the same 1.381 ft³ net volume:
- total net volume: 1.381 × 8 = 11.048 ft³
- 50 lb bags: 11.048 ÷ 0.375 = 29.46, rounded up to 30 bags
- 80 lb bags: 11.048 ÷ 0.60 = 18.41, rounded up to 19 bags
If you batch each post separately and round up per post, 4 bags × 8 = 32 bags for the 50 lb product, which is more than the 30-bag total. That may be practical if you cannot share a part-used bag between posts; it is not a mathematical requirement. Decide based on how you mix and place the concrete.
The calculator's quantity input multiplies the same gross form. It does not subtract the post. Use its volume as the gross volume, subtract the post volume in your notes, and then divide by the bag yield. If you use the calculator's bag count directly, treat it as an upper bound.
What this estimate does not decide
This is a volume and bag-count estimate. It does not:
- design a fence, post, or foundation;
- determine frost depth, soil bearing, drainage, or embedment requirements;
- select a concrete mix, strength, or admixture;
- check local codes, permits, or inspection requirements;
- account for an irregular, belled, or over-excavated hole;
- replace the product's installation instructions.
QUIKRETE's post-setting guide is a manufacturer's method, not a building code. Local requirements can differ, especially for frost depth, wind exposure, and soil conditions. Confirm the design and inspection requirements with the local building department or a qualified professional.
Sources: QUIKRETE, “Setting Posts in Concrete”; QUIKRETE Fast-Setting Concrete Mix data sheet; QUIKRETE Concrete Mix No. 1101 data sheet. Checked October 20, 2026. Verify the current package or technical sheet before ordering.
FAQs
How much concrete do I need for a fence post?
It depends on the hole diameter, concrete fill height, post size, and bag yield. For the example on this page—10 in hole, 3 ft concrete fill, 3.5 in square post—the net volume is about 1.381 ft³, or 4 bags of 50 lb mix at 0.375 ft³ per bag.
Does the Concrete Calculator subtract the fence post?
The Round column mode calculates the gross cylinder. It does not subtract the post. Subtract the embedded post volume yourself if you need a net quantity; otherwise the calculator's bag count is a conservative upper bound.
How wide and deep should a fence post hole be?
QUIKRETE's guide suggests a hole about three times the post width and a depth of one-third to one-half of the above-ground post length plus 6 inches, with a 6-inch gravel base. That is manufacturer guidance, not a universal rule. Follow the project plan and local requirements for frost depth and soil conditions.
How many bags of concrete for 8 fence posts?
Using the example's 1.381 ft³ net volume per post, 8 posts need about 11.05 ft³. At 0.375 ft³ per 50 lb bag, that is 30 bags; at 0.60 ft³ per 80 lb bag, 19 bags. Recalculate with your actual hole and post dimensions.
Should I use fast-setting concrete or regular concrete mix?
Both can set posts, but their yields and working times differ. Fast-setting mix is designed for a quick set; a regular mix may give more working time. Use the product instructions and the yield on the exact bag, and do not substitute one product's yield for another.
Do I need gravel at the bottom of the hole?
QUIKRETE's post-setting guide recommends a 6-inch gravel base for drainage. That is a manufacturer recommendation for its method, not a universal requirement. Follow the project details and local guidance, and account for the gravel when you calculate the concrete fill height.