Concrete & Masonry · Concrete & Masonry
How to Calculate Concrete for a Sonotube
A Sonotube is a cylinder: calculate the circular area, multiply by the filled height, then divide by the product yield and round the final bag count up.
Concrete for a Sonotube = π × (inside radius)² × filled height. Convert the result to cubic feet, divide by the yield on the exact bag, multiply by the number of identical tubes, and round only the final bag count up.
The Concrete Calculator has a round-column mode that follows this model. This guide explains which measurement belongs in each input and how the geometry differs from the product step. A form tube is a way to hold concrete while it sets; the calculation does not choose a footing size, reinforcement, embedment depth, or local design requirement.
The short answer
A Sonotube or similar cardboard form is a cylinder. Measure the inside diameter, the height that will actually be filled with concrete, and the number of identical tubes. Use one unit system before multiplying:
radius = inside diameter ÷ 2
volume per tube = π × radius² × filled height
total volume = volume per tube × quantity
bags = ceiling(total volume ÷ yield per bag)
The calculator keeps the volume fractional and rounds the package count up because a partial bag is not a whole purchase unit. Enter the yield printed on your product label or technical sheet; bag weight alone does not tell you the finished volume.
Measure the tube and filled height
Use the tube's inside diameter, not the outside diameter or the nominal label if the form has a thick wall. Measure the concrete height from the bottom of the pour to its finished top. If a gravel base, void, or unfilled section is inside the tube, do not include that portion in the filled height.
QUIKRETE's current QUIK-TUBE data sheet lists 8, 10, and 12 inch diameters for a common 4-foot form and publishes the concrete amount for each size. Those dimensions describe that product line; another form may have a different internal diameter or length. Check the form you are using and follow its installation instructions.
If the form is cut shorter, use the cut length. If several tubes have different heights, calculate each group separately and add the unrounded volumes. This avoids hiding a different diameter or fill depth inside one average.
Use the cylinder formula
For dimensions in feet, the volume is:
volume (ft³) = π × (diameter in feet ÷ 2)² × height in feet
When both diameter and height are entered in inches, convert the result with the cubic-inch relationship:
volume (ft³) = π × diameter_in² × height_in ÷ 6,912
The denominator is 12³ because one cubic foot contains 1,728 cubic inches and the radius contributes the factor of 4. Do not divide a cubic-inch result by 12; that would apply a linear conversion to a volume.
Worked example: an 8-inch by 4-foot tube
Suppose one tube has an 8-inch inside diameter and a 4-foot concrete height.
- Convert the diameter: 8 ÷ 12 = 0.666667 ft.
- Find the radius: 0.666667 ÷ 2 = 0.333333 ft.
- Find the circular area: π × 0.333333² = 0.349066 ft².
- Multiply by height: 0.349066 × 4 = 1.3963 ft³.
- Convert to cubic yards if useful: 1.3963 ÷ 27 = 0.0517 yd³.
For a product yielding 0.375 ft³ per 50 lb bag, 1.3963 ÷ 0.375 = 3.7235 bags, so buy 4 bags before any separately chosen allowance. For a product yielding 0.60 ft³ per 80 lb bag, 1.3963 ÷ 0.60 = 2.3272, so the whole-bag result is 3 bags. The two answers differ because the product yields differ, not because the tube volume changed.
QUIKRETE's project sheet gives the same type of check as bags per linear foot: for an 8-inch tube it lists about 0.9 of a 50 lb bag or 0.6 of an 80 lb bag per foot. Across four feet those figures are 3.6 and 2.4 bags, which round to the same 4 and 3 whole bags. Treat the table as a product example and verify the current package.
Convert volume to bags and repeat the form
Use the exact volume until the package step:
adjusted volume = total volume × (1 + allowance rate)
whole bags = ceiling(adjusted volume ÷ product yield)
An allowance can cover an uneven base, spillage, or measurement uncertainty, but it is an input you choose rather than a universal Sonotube percentage. Show the base volume first so someone reviewing the estimate can see whether the cylinder measurement is correct.
For ten identical 8-inch by 4-foot tubes, the base volume is 1.3963 × 10 = 13.963 ft³. At 0.60 ft³ per bag, 13.963 ÷ 0.60 = 23.271 bags, so the purchase count is 24 bags with no allowance. If each tube is a separate batch, practical batching may require more than one final combined rounding step; follow the product instructions and placement plan.
Account for a post inside the tube
An empty round form uses the full cylinder. A tube poured around a post uses the cylinder minus the volume occupied by the embedded post. If the post is round, subtract a second cylinder. If it is square or rectangular, subtract post width × post depth × embedded height.
The Fence Post Concrete Calculator includes hole diameter, post diameter, fill depth, post count, bag yield, and allowance. It is useful when its circular post model matches the job. Do not subtract the post in both the tube calculation and the post-hole calculation, and do not use a post-hole model when the tube is a solid column with no embedded post.
What this estimate does not decide
This calculation does not choose the tube diameter, footing dimensions, frost depth, reinforcement, bearing capacity, concrete strength, placement method, or local permit/code requirement. It assumes a straight cylinder with a constant inside diameter and a known filled height. Bell-shaped holes, flared bases, multiple diameters, sloped tops, and voids need separate shapes.
For a structural pier, deck footing, fence, sign, or other load-bearing work, use the project plans and the applicable local requirements. The arithmetic can check a quantity after those decisions are made; it cannot approve the design.
Product reference: QUIKRETE® QUIK-TUBE® Building Forms data sheet and QUIK-TUBE® Pillar Foundations project guide. Checked October 22, 2026. Product sizes, yields, and instructions can change; verify the form and bag you will buy.
FAQs
How many bags of concrete do I need for a 10-inch Sonotube?
You need the filled height and the product yield. For one 10-inch tube filled 4 feet high, the cylinder is about 2.182 ft³. That is 5.82 bags at a 0.375 ft³ yield, rounded to 6 bags, or 3.64 bags at a 0.60 ft³ yield, rounded to 4 bags.
Do I use the tube's outside diameter?
No. Use the concrete-filled inside diameter. A thick form wall makes the outside measurement larger than the cylinder of concrete.
Should I use a Sonotube table or the formula?
Use the formula for the exact diameter and height. A manufacturer table is a useful cross-check when it covers the same form and product yield; it is not a universal bag rule.
Does a Sonotube calculator choose the footing size?
No. It estimates volume from dimensions you provide. Footing size, reinforcement, soil assumptions, and local requirements are separate design decisions.